dnipro-modular-metamorph

Dnipro Modular Metamorph

Three-channel four-stage sequenced CV controller with glide

20 HP Eurorack module

Metamorph is a 4-stage, 3-channel sequenced controller for Eurorack that outputs CV and gate signals across three independent channels simultaneously. It offers both factory and user-programmable sequences, per-channel glide, CV-addressable stage selection, and a master/slave link mode for expanding to eight steps. Its musical character is versatile and hands-on, suited for melodic sequencing, CV modulation, and generative patch work.

Features

  • 4-stage, 3-channel simultaneous CV sequencer
  • Per-channel glide (portamento) control for each of 3 channels
  • User-programmable sequence with non-volatile memory storage
  • Factory-programmed sequence mode
  • CV Input for direct stage addressing (0-5V), with sample-and-hold when clocked
  • Reverse input for direction control (does not work in User Sequence mode)
  • Hold/Stop input to freeze sequencer on current stage
  • Individual gate outputs for each of 4 stages (outputs +5V while stage is active)
  • Triggers output fires each time the stage changes
  • Output voltage range selectable via PCB jumpers: -5V/+5V, -2.5V/+3V, 0V/+11V, 0V/+6V
  • Master/Slave link mode for two modules to create an 8-step sequencer with doubled outputs
  • Pendulum mode possible by patching Gate Out to Reverse In

Controls & Jacks (33)

  • Channel 1 Stage 2— Channel 1 Stage 2
  • Channel 2 Stage 1— Channel 2 Stage 1
  • Channel 3 Stage 3— Channel 3 Stage 3
  • Channel 1 Stage 3— Channel 1 Stage 3
  • Channel 3 Stage 1— Channel 3 Stage 1
  • Channel 3 Stage 2— Channel 3 Stage 2
  • Channel 3 Stage 4— Channel 3 Stage 4
  • Channel 2 Stage 2— Channel 2 Stage 2
  • Channel 2 Stage 3— Channel 2 Stage 3
  • Channel 1 Stage 1— Channel 1 Stage 1
  • Channel 2 Stage 4— Channel 2 Stage 4
  • Channel 1 Stage 4— Channel 1 Stage 4
  • Stage Gate Out 1— Outputs +5V as long as Stage 1 is the currently active stage. Goes low when any other stage is active.
  • Stage Gate Out 2— Outputs +5V as long as Stage 2 is the currently active stage. Goes low when any other stage is active.
  • Triggers Output— Outputs a trigger pulse every time the sequencer moves to a new stage. Useful for triggering envelopes in sync with sequence changes.
  • Hold Input— When it receives a signal, the sequencer stops. To restart, send a gate to Reset Input or press any stage select button.
  • Stage Gate Out 3— Outputs +5V as long as Stage 3 is the currently active stage. Goes low when any other stage is active.
  • Stage Gate Out 4— Outputs +5V as long as Stage 4 is the currently active stage. Goes low when any other stage is active. Tip: patching any Gate Out to Reverse
  • Channel 2 Glide— Channel 2 Glide
  • Channel 1 CV Output— Outputs the CV value set by the Channel 1 stage knobs for the currently active stage. Voltage range set by jumper on back: approximately -5v
  • Reverse Input— When it receives a signal, the direction of sequencer travel flips. Not active in User Sequence mode. Tip: patch Stage Gate Out to Reverse I
  • Channel 1 Glide— Channel 1 Glide
  • Reset Input— Receives a trigger or gate to reset the sequencer back to Stage 1. Also restarts the sequencer if it was stopped by the Hold input.
  • CV Input— Accepts 0–5V to select the active stage via voltage. When clock is also patched, CV is sampled and held in sync with the clock. Not active i
  • Channel 3 CV Output— Outputs the CV value set by the Channel 3 stage knobs for the currently active stage. Voltage range set by jumper on back. Glide applies her
  • Channel 2 CV Output— Outputs the CV value set by the Channel 2 stage knobs for the currently active stage. Voltage range set by jumper on back. Glide applies her
  • Clock Input— Accepts regular clock or any trigger signal. Each trigger advances the sequencer one step. When patched, stage knobs require holding stage b
  • Channel 3 Glide— Channel 3 Glide
  • Stage 3 Select— Stage 3 Select
  • Stage 2 Select— Stage 2 Select
  • User Sequence— User Sequence
  • Stage 4 Select— Stage 4 Select
  • Stage 1 Select— Stage 1 Select

How-To Guides

  • Save a Custom User Sequence
  • Load and Play a Saved User Sequence
  • Simple 4-Note Melody
  • Triple CV Modulation Source
  • Pendulum Back-and-Forth Sequence
  • Gliding Bass Line
  • CV-Addressed Chord Snapshot Player
  • Rhythmic Gate Pattern Generator
  • 8-Step Sequence with Two Linked Modules
  • Live Performance Hold and Fill

Explore the interactive Metamorph panel on BleepDex — tap any control to learn what it does.

8c571ce